• No results found

From the above analyses and experiments, some modifications should be conducted in the rig to achieve better performance. Suggestions are as follows:

1. More power is expected for the heating device to obtain higher temperature. It is recommended to use a larger but shorter heating element to increase the power.

Chapter 7 Conclusions and Recommendations 177 2. Electric brushes and commutators should be relocated further from the heating disk to

decrease oxidation of copper, and hence they should be shielded as m u c h from the heat as possible.

3. Omit the heating device cutoff circuit to keep the heating device on when pausing the experiment.

4. Decrease significant warpage of heating disk. We can increase the thickness of the disk and decrease the width of the disk ring, and can modify the mechanical device on the supporting b e a m of the roller to m a k e the roller and the warping disk contact m o r e evenly over the roller width.

5. Need to introduce water cooling to the roller to simulate rolling process, and computer can control it on- or off- operation.

6. Using hydraulic jack to apply the load, which can be controlled by the computer.

7. Two rollers with different materials should be tested at the same time to provide qualitative and quantitative indications of their wear and friction characteristics.

8. Different roll bite lubricants should be applied in the experiment.

References

References 179 1. S. Spuzic, et al, W e a r of hot rolling mill rolls: an overview, Wear, 176,1994

2. S. Lunderg, A new high-temperature test rig for optimization of materials for hot-rolling rolls, Journal of Materials Processing Technology, 36,1993

3. G. E. Dieter, Mechanical Metallurgy, McGraw-Hill Book Company, 1988

4. H. Hertz, Uber die Beriihrung fester elastischer KSrper (On the contact of elastic solids). J. reine und angewandte Mathematik, 92, 1882

5. F. F. Ling, et al, Contact and surface mechanics, 75th Anniversary Commemorative Symposium of the A S M E Research Committee on Tribology, 1990

6. K. L. Johnson, Contact Mechanics, Cambridge University Press, 1985

7. F. W. Carter, On the action of a locomotive driving wheel, Proceedings of the Royal Society, 1926

8. H. Poritsky, Stresses and deflections of cylindrical bodies in contact Trans, of A S M E , Series E, Journal of Applied Mechanics, 17, 1950

9. R. D. Arnell, et al, Tribology Principles and Design Applications, Macmillan, 1991 10. D. F. Moore, Principles and Applications of Tribology, Oxford, 1978

11. L. H. Bennett Economics Effects of Metallic Corrosion in the United States, a Report to Congress, National Bureau of Standards, March 1978

12. D. Godfrey, Wear Control Handbook, ASME, 1980

13. F. F.Ling, et al, Approaches to Modelling of Friction and Wear, Springer-Verlag, 1988

References 180 14. H. C. M e n g , et al. Wear models and predictive equations: their form and content Wear, 181-183, 1995

15. S. Bahadur, Wear research and development ASME J. Lub. Technology, 100, 1978

16. R. G. Bayer, Mechanical Wear Prediction and Prevention (Part 2), Marcel Dekker, 1994

17. J. F. Archard, J. Application of Physics, 24, 1953

18. W. H. Tait, Roll shop, Chapter 12 in Rolls for the Metal working Industries, R. B.

Corbett, ISS-AIME, 1990

19. B. Spencer et al, Mechanical Working and Steel Processing, 1984

20. W. Z. Wujtow, et al, Surface treatment of rolls for special applications, Chapter 14 in Rolls for the Metalworking Industries, R. B. Corbett, ISS-AIME, U S A , 1990

21. S. Iwadoh, et al, Effect of work roll materials and progress of manufacturing technology on cold rolling and future developments in Japan, ISIJ International,

Vol.32, N o . 11

22. L&R Ashboly Pty Ltd, Advanced Solution for Industrial Protection, High Velocity Coatings, Vol. 109, June 1992

23. H. Kodama, etal, J. Japan Institution of Material, 29,1990

24. A. Kiesel, Tribological behaviour of bold rolling mill work roll steel during rolling-sliding wear testing, Bachelor thesis, University of Wollongong, November 1995

25. M. S. Aziz, The effects of lubricants and scale upon friction in hot flat rolling, PhD thesis, University of Sheffield, M a y 1980

References 181

26. C. L. Robinson, et al, Roll lubrication in hot strip mills, B S C Publication Report, CEL/PH/1/73,1973

27. R. V.Williams, et al, Roll surface deterioration in hot strip mills, J. of the Iron and Steel Inst, 203, 1965

28. W. H. Betts, et al, Rolls used in today's rolling mills, Chapter 2 in Rolls for the Metalworking Industries, R. B. Corbett, I S S - A I M E , U S A , 1990

29. J. J. deBarbadillo, et al, Mechanism of banding in hot strip mill work rolls, Iron and Steel Engineer, January 1981

30. S. Lundberg, et al, The influence of rolling temperature on roll wear investigated in a n e w high temperature test rig, Journal of Materials Processing Technology, 42,1994

31. J. A. Schey, Tribology in Metalworking; Friction, Lubrication and Wear, American Society for Metals, 1983

32. R. N. Shaughnessy, Wear and life of hot strip mill rolls, J. Iron and Steel Inst., 206, 1968

33. P. G. Stevens, et al, Increasing work-roll life by improved roll-cooling practice, J.

Iron and Steel Inst, 209, 1971

34. W. J. Williams, Banding in hot strip mill work rolls, Iron and Steel, August 1962 35. Y. Seckimoto, et al, Effects of rolling condition on the surface temperature of work

roll in hot strip mills, Iron and Steel Inst, of Japan, 16,1976

36. L. C. Erickson, et al, Analysis of banded hot rolling rolls, Wear, 165,1993 37. Y. Beers, Introduction to the Theory of Error, Addison-Wesley, 1957

References 182

38. J. R. Taylor, A n Introduction to Error Analysis, University Science Books, 1982

39. J. A. Stankovic, Advances in Real-time Systems, IEEE Computer Society Press, 1993

40. S. Bennett Real-time Computer Control: An Introduction, Prentice-Hall, 1988 41. L. Finkelstein, et al, Concise Encyclopedia of Measurement and Instrumentation, Pergamon Press, 1994

42. D. L. Ripps, An Implementation Guide to Real-time Programming, Yourdon Press, 1989

43. P. A. Laplante, Real-time Systems Design and Analysis (An Engineer's Handbook), I E E E Press, 1993

44. R.V. Williams, Acoustic Emission, AdamHilger Ltd, 1980

45. J. Pumwa, An experimental study of friction and adhesive wear, Master thesis, University of Wollongong, April 1991

46. L. J. Andrew, Rolling-sliding wear behaviour of low alloy gear steels, Bachelor thesis, University of Wollongong, November 1994

47. B.C. Kuo, Time-domain design of control system, Chapter 9 in Automatic Control System, Prentice-Hall International, Inc. 1989

48. P.J. Blau, Friction, lubrication, and wear technology, Volume 18 in ASM Handbook, A S M International, 1994

49. S. Cerni, et al, Temperature and thermal stresses in rolling of metal strip, Iron and Steel Engineer Year Book, 1963

References 1 8 3

50. D. Park, et al, Temperature effects of cooling work rolls, Iron and Steel Engineer, November 1972

51. C. N. Hammil, et al, Why did that roll break? Iron and Steel Engineer, June 1974 52. Lubrication Fundamentals Commitee of ASLE, Friction and Wear Devices, Park

Ridge, 1976

53. M. L. James, et al, Applied Numerical Methods for Digital Computation, Harper Collins College Publishers, 1993

54. G. D. Spenceley, Progress report on hard chrome plated rolls for cold rolling, The British Iron and Steel Research Association, Mechanical Working Division Rolling

Committee, 1963

55. R. W. Nichols, Acoustic Emission, Applied Science Publisher, 1976

56. V. B. Ginzburg, Steel Rolling Technology; Theory and Practice, Marcel Dekker, 1989.

57. K. Z. Gahr, Microstructure and Wear of Materials, Elsevier, 1987

58. J. A. Schey, Introduction to Manufacturing Processes, Macgraw-hill, 1987 59. G. Savage, Hot wear testing of roll alloys, BHP Research, Private

communication, 1995

60. J. W. Russell, Work roll banding — a rollmaker's overview, RMJ7AISE seminar, November 1977

61. A. Ohnuki, et al, Advanced Technology of Plasticity, 1984

References 1 8 4 62. A. Magnee, et al, Wear behaviour of steels for hot rolling mill rolls, C R M 57,

1980

63. W. L. Roberts, Frictional effects in hot rolling, Hot Rolling of Steel, Marcel Dekker, 1983

64. K. Nishizawa, et al, Effect of rolling oil on hot strip rolling, The Sumitomo Search 17, 1977

65. N. N. Bulkin, Coefficient of friction in rolling of R9 steel with electric heating, Russian Metallurgy, January 1991

66. L&R Ashbolt Pty Ltd, C-Ramachrome-Densification of Chrome Plate, Modem Coatings for Industrial Protection, Vol 13, June 1992

67. G. M. Bragg, Principles of Experimentation and Measurement, Prentice-Hall, 1974

Appendices